tel-profile
This command configures the Tel Profiles table, which lets you define Tel Profiles.
Syntax
(config-voip)# coders-and-profiles tel-profile <Index> (tel-profile-<Index>)#
|
Command |
Description |
|---|---|
|
Index |
Defines the table row index. |
|
call-priority-mode |
Defines the call priority mode. |
|
coders-group |
Defines the coders group name. |
|
current-disconnect |
Enables current disconnect. |
|
dial-plan-index |
Defines the dial plan index. |
|
digit-delivery |
Enables automatic digit delivery to the Tel side after the line is off-hooked or seized. |
|
digital-cut-through |
Enables a call connection without the On-Hook/Off-Hook process 'Cut-Through'. |
|
disconnect-on-busy-tone |
Releases the call if the gateway receives a busy or fast busy tone before the call is answered. |
|
dtmf-volume |
Defines the DTMF generation volume. |
|
early-media |
Enables early media. |
|
echo-canceller |
Enables echo cancellation (i.e., echo from voice calls is removed). |
|
echo-canceller-nlp-mode |
Configures EC NLP mode. |
|
enable-911-psap |
Enables 911 PSAP. |
|
enable-agc |
Activates AGC (Automatic Gain Control). |
|
enable-did-wink |
Enables support for DID lines using Wink. |
|
enable-voice-mail-delay |
Enables voice mail delay. |
|
fax-sig-method {no-fax|t.38-relay|g.711-transport| fax-fallback|g.711-reject-t.38} |
Defines the SIP signaling method for establishing and transmitting a fax session when the device detects a fax. |
|
flash-hook-period |
Defines the flashhook detection and generation period (in msec). |
|
fxo-consult-call-transfer {disable|enable} |
Enables support for FXO consultative call transfers (initiated by PSAP operators) for emergency (NG9-1-1) calls, based on the NENA i3 Standard for Next Generation 9‑1‑1 (NENA-STA-010.2-2016). |
|
fxo-double-answer |
Enables FXO double answer. All incoming TEL2IP call are refused. |
|
fxo-ring-timeout |
Defines the delay (in 100 msec) for generating an INVITE after RING_START is detected. |
|
input-gain |
Defines the TDM input gain. |
|
ip2tel-cutthrough_call_behavior |
Enables a call connection without an On-Hook/Off-Hook process. |
|
is-two-stage-dial |
Configures Dialing Mode - One-Stage (PBX Pass-thru) or Two-Stage. |
|
jitter-buffer-maximum-delay |
Defines the maximum delay (in msec) for the Dynamic Jitter Buffer. |
|
jitter-buffer-minimum-delay |
Defines the minimum delay (in msec) for the Dynamic Jitter Buffer. |
|
jitter-buffer-optimization-factor |
Defines the Dynamic Jitter Buffer frame error-delay optimization factor. |
|
mwi-analog-lamp |
Enables MWI support using an analog lamp (110 Volt). |
|
mwi-display |
Enables MWI support using Caller ID interface. |
|
mwi-ntf-timeout |
Defines the maximum duration (timeout) that a message waiting indication (MWI) is displayed on endpoint equipment (phones' LED, screen notification or voice tone). |
|
play-bsy-tone-2tel |
Configures Don't play, Play Busy or Reorder tone when disconnecting ISDN call and Send PI=8, Play before disconnect. |
|
polarity-rvrsl |
Enables Polarity Reversal. |
|
profile-name |
Defines the Profile Name (string). |
|
prog-ind-to-ip |
Determines whether to send the Progress Indicator to IP. |
|
rtp-ip-diffserv |
Defines the RTP IP DiffServ. |
|
signaling-diffserv |
Defines the SIP Signaling DiffServ. |
|
swap-teltoip-phone-numbers |
Swaps Tel to IP phone numbers. |
|
tel-preference |
Defines the Profile Preference - the priority of the Tel Profile. |
|
time-for-reorder-tone |
Defines the duration of the reorder tone that plays before the FXO releases the line [seconds]. |
|
voice-volume |
Defines the voice TDM output gain. |
Command Mode
Privileged User
Example
This example configures a Tel Profile:
(config-voip)# coders-and-profiles tel-profile 0 (tel-profile-0)# profile-name PSTN (tel-profile-0)# activate